Sponge bar alternative…

Thanks for the question!  Please let me know if you need more information. Step by step is below.  Did the pics tonight, hope they help!

In my Kantan Bulky original post I had replaced the sponge bar in my Kantan Bulky and Empisal ribber with 3/16 inch copper U channel (stained glass supply store) and bias tape folded in half. After a while the bias tape settled and I knew that wasn’t a permanent solution. So I searched you tube and after watching this video came up with a great alternative. You see, if the sponge material will fill the sponge bar cavity, you don’t need the metal bar anymore!! I got some 1/2 inch *20 foot backer rod insulation foam from Walmart, one bag is about $4.00. though 3/8 or smaller may have been easier, 1/2 inch worked fine, cut in half lengthwise.

You’ll find it in the hardware section by the weatherstripping.

How to do it.


Gather your tools and a roll of masking tape. The wrench or driver size is 5.5mm, you also need a small Phillips screwdriver, and a pair of scissors.

1. Tape all needle heads so the needles don’t move during this. You will save ALOT of grief.

2. Clamp machine bed to the edge of a table, then carefully remove the flat head Phillips screws, nut and washer from the needle retaining bar at the front of the machine, this is the metal piece the needles are secured with. Its best to hold the screw in place and loosen the nut from underneath, so you dont strip the screws. Don’t remove the outside edge (rounded machine screws) yet.

3. Measure out a piece of foam long enough to fill the channel from left to right, and cut lengthwise in half.

4. Remove all but the far left screw and gently slide the metal retaining bar (in the pic above with the colored ink) forward slightly, allowing access to the sponge bar channel from the top.

5. Carefully insert the sponge into the cavity, it should rest on top of the needles. Once you reach half way, carefully remove the left edge screw and replace the far right edge screw, continuing to fill the sponge bar cavity.

6. Carefully push the metal retaining bar back into place, inserting left edge screw first. Then replace the inside edge screws.

7. Insert the flathead screws across the retaing bar and fasten with washer and nut.

8. Remove masking tape, push needles back and forth a few times to settle the sponge in place. The needles should move with a little tension. They should not be loose or free sliding, and should not be difficult to move either.

9. Replace knitter carriage and Cast on!

Hope this helps. Please like if it does🤗

Best wishes!!



Mulberry, eggplant, lavender, lilac, ….it’s not purple rain.

So in the beginning of 2016, yes 2016! I started on this neckwarmer. I’ve finally picked it up for the last time.

It’s not quite purple ( though I thought purple rain was a clever name for the pattern) I think mulberry captures the name if the color best. This was a thrift store sweater, carefully un-seamed, unraveled and cleaned. In all this was the cowl neck and parts of the sleeves. The donor sweater was pilled and felted in places, I couldn’t use it all. Now tightly knit, it’s very supple, and my only regret is not re-spinning with the multicolored sulky thread, as I did in the original swatch…..maybe next time. I’m super pleased with results as they were worth the effort entirely!

I have a free pattern written up if you would like to try it. Always happy for feedback! You can message me, I can email it.

Just haven’t figured out how to post it here!

Ruby’s Vintage Patterns

88eed67327562aa38c6346e8f8e6c4d0
Transcontinental Ruby’s Story begins.

What’s up with Ruby’s Vintage Patterns? Well, Ruby was a really hard working woman in her time. Her life has unfolded before my eyes over the past 12 years and I am truly interested in sharing her story. So in Project number 1, I am knitting the garment using the materials originally called for in her 1960s written pattern. As I do, I am also searching for that perfect 21st century yarn to work the design in parallel. I think Ruby deserves to have her patterns revived, as they are universal, practical designs, meant for us “normal knitters”.  We like Simple & Practical.  We know if we are going to spend X amount of time hand knitting the garment, then you need quality materials that will hold up to the XX wear and easy care you hope the intended user will give it!!  I truly like knitting things that people will actually use! So look forward to explaining more about Ruby, her patterns and her story.

 

Friday fluff

 

This bowl of Friday fluff brought to you by Buddy, a 2 year old French Angora house bunny.  Stay Warm!!

img_20161209_222009
WHAT IS THIS PLANT?                                                                 Found on Minnesota shore of Lake Superior

Please comment if you know what this is!!!

Copperella

Goldilocks originally though I should call this one goldilocks…But after sleeping on it I like Copprella…it’s the name this yarn will have. Copperella was made in China from polyester, cotton and 3% “unknown” materials (the sequins and tinsel-like gold) Maybe Rumplestiltskin would be more appropriate. After all he taught the girl to spin straw into gold.

31334132301_ac995feeab_o

Though I’m sure it didn’t start out as straw, the color caught my eye, it’s warm.  The texture is silky, not scratchy as  many metallic-look yarns can be.

Copperella will be processed and measured, the reused in an open-lace pattern. I might add a strands of teal, orange, or purple….follow me later in projects!

 

Fall Fluff

WHO WOULDN’T WANT TO TOUCH THIS FIBER?

At October’s close, we had a gorgeous fall day and I collected some milkweed pods.  I have every intention of spinning all of it.  I did make a supported spindle from a pine nut and a piece of wire to try it out.  It was relaxing! Every turn of the spindle spread the fresh pine oil into the crisp air. I love camping and finding treasures to inspire.img_20161028_122446397

Riveting bed time story.. THE WOOL PRODUCTS LABELING ACT OF 1939

Pondering the correct words to classify reused yarn shouldn’t be so tough, right? Last year I began toying with using the words Recycled/Reclaimed/Repurposed on product labels.

IMG_20160103_241151975_HDRTurns out there is much to learn on this subject.  So far, best-case is to stick with the guidance provided by a 75 year old law.THE WOOL PRODUCTS LABELING ACT OF 1939 as amended, 2014.

(b) Where a wool product is composed in part of wool, or recycled wool and in part of unknown and, for practical purposes, undeterminable non-woolen fibers reclaimed from any spun, woven, knitted, felted, braided, bonded or otherwise manufactured or used product, the required fiber content disclosure may, when truthfully applicable, in lieu of the fiber content disclosure otherwise required by the Act and regulations, set forth (1) the percentages of wool or recycled wool, and (2) the generic names and the percentages of all other fibers whose presence is known or practically ascertainable and (3) the percentage of the unknown and undeterminable reclaimed fibers, designating such reclaimed fibers as “unknown reclaimed fibers” or “undetermined reclaimed fibers,” as for example:
75% Recycled Wool – 25% Unknown Reclaimed Fibers.
35% recycled Wool – 30% Acetate – 15% Cotton – 20% Undetermined Reclaimed Fibers.
In making the required fiber content disclosure any fibers referred to as “unknown reclaimed fibers” or “undetermined reclaimed fibers” shall be listed last.
(c) The terms unknown recycled fibers and undetermined recycled fibersmay be used in describing the unknown and undeterminable reclaimed fibers referred to in paragraph (b) of this rule in lieu of the terms specified therein, provided, however, That the same standard is used in determining the applicability of the term recycled as is used in defining “recycled wool” in section 2(c) of the Act.

Defined in 2c of the Act…..

15 U.S. Code § 68 – Definitions  (for 16 U.S. Code part 300)
The term “recycled wool” means (1) the resulting fiber when wool has been woven or felted into a wool product which, without ever having been utilized in any way by the ultimate consumer, subsequently has been made into a fibrous state, or (2) the resulting fiber when wool or reprocessed wool has been spun, woven, knitted, or felted into a wool product which, after having been used in any way by the ultimate consumer, subsequently has been made into a fibrous state.

If I produce a textile product entirely of recycled wool, must I list the country of origin of that recycled wool? Do I use the country of the wool’s origin or the country in which it was recycled? Hmmm. This was better explained here.

To promote consistency with the Textile Rules, the Commission proposed to update §300.25(d) to state that an imported product’s country of origin as determined under the laws and regulations enforced by U.S. Customs and Border Protection (‘‘Customs’’) shall be the country where the product was processed or manufactured.

Now …is that product made in the USA from recycled wool from “country or origin” ? Hmmmm.